For the most up-to-date version, visit: goo.gl/r5lc5O

Additional data collection includes:

1. Driver Distraction Monitoring
2. Temperature Monitoring for refrigerated fleets
3. Tire Pressure Monitoring

For more information regarding Third-Party Devices and data collection through Geotab Partners, visit: www.geotab.com.

IOX hardware technical specifications

✱ NOTE: When installed in a vehicle, The IOX-CAN and third-party devices derive the supply voltage level from the car battery. IOX-CAN is not suitable for direct connection to an engine bus.

Data transmission rates

The third-party CAN interface adjusts its baud rate based on the baud rate of the connected CAN bus (either 250 kbps or 500 kbps). The IOX-CAN must receive a minimum of one message to set the baud rate. Shorting jumper pin A and jumper pin B together enables the internal 120 Ohm terminating resistor — required if the application itself is not already terminated.

IOX installation instructions

! IMPORTANT: Professional installation (Certified Geotab® Installer or equivalent) is required for the safe and proper installation of this product (harness and/or IOX). The installer must have sufficient technical knowledge and expertise for the respective installation.

WARNING! Always read and follow all safety information, including Important Safety Information and Limitations of Use, before harness and/or IOX installation. Disconnect the GO device from the vehicle before installation and connect it post-installation (see goo.gl/rkLRiA). Failure to follow these instructions and warnings can result in loss of vehicle control and serious injury or vehicle damage.

Installing the IOX-CAN

Termination shunt

The IOX comes with a termination shunt installed in the expansion port. If you plan to install more than one IOX in a daisy chain, you must remove the shunt from each device in the line, with the exception of the last IOX connected. The shunt must remain in the last IOX and secured with a zip tie.

The shunt in the last IOX device ensures the GO device detects and configures the IOX, as effectively as possible.

✱ NOTE: Failure to install the shunt in the last IOX may affect IOX communication. To ensure the IOX communicates, please secure the shunt using a zip tie.

Valor

To log temperature every five minutes from the Valor TempTrac solution, apply the following custom parameter to the GO device using the MyGeotab software:

<GoParameters><Parameter Description=" Log Reefer Temp Periodically" Offset="180" Bytes="02"/></GoParameters>

This functionality requires GO device firmware XXX.20.43 or higher.

Important safety information and Limitations of Use

For the latest version of the Limitations of Use, visit: goo.gl/k6Fp0w.

WARNING! Do not attempt to install, configure or remove any product from any vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked. Attempting to service units while being operated could result in malfunctions or accidents, leading to death or serious personal injury.

WARNING! All in-vehicle devices and related cabling must be securely fastened and kept clear of all vehicle controls, including gas, brake and clutch pedals. You must inspect devices and cabling on a regular basis to ensure all devices and cabling continue to be securely attached. Loose cabling or devices may impede the use of vehicle controls, resulting in unanticipated acceleration, braking or other loss of vehicle control, which could lead to death or serious personal injury. Improperly fastened in-vehicle devices may detach and impact operators upon sudden acceleration or deceleration, which may cause injury.

WARNING! If at any point after an in-vehicle device is installed a warning light illuminates on the vehicle dash or the vehicle stalls or has a marked drop in performance, shut off the engine, remove the device, and contact your reseller. Continuing to operate a vehicle with these symptoms can cause loss of vehicle control, and serious injury.

WARNING! Your in-vehicle devices must be kept clear of debris, water and other environmental contaminants. Failure to do so may result in units malfunctioning or short-circuiting that can lead to a fire hazard or vehicle damage or serious injury.

WARNING! Do not attempt to remove the devices from the vehicle in which they are originally installed for installation in another vehicle. Not all vehicles share compatibility, and doing so may result in unexpected interactions with your vehicle, including sudden loss of power or shutdown of the vehicle’s engine while in operation or cause your vehicle to operate poorly or erratically and cause death or serious injury and/or vehicle damage.

NOTICE: This product does not contain any user-serviceable parts. Configuration, servicing, and repairs must only be made by an authorized reseller or installer. Unauthorized servicing of these products will void your product warranty.

Regulatory statements

USA

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

✱ NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: